橡膠雙頭磨片機是檢測儀器，zhuan gong橡膠廠及防水卷材廠磨制橡膠試片到一定厚度供其他試驗設備進行試驗。主要是由機座進給拖板、工作輪、吸塵器、電動機、砂輪等主要部件組成。形成了粗、細兩種砂輪同時工作，具有一機兩用的特點。
The rubber double-head mill is a testing instrument. Zhuan gong rubber factory and waterproof coil factory grind rubber test pieces to a certain thickness for testing by other test equipment. It is mainly composed of the main parts such as the carriage feed tray, work wheel, vacuum cleaner, motor, and grinding wheel. The coarse and fine grinding wheels are formed to work at the same time, which has the characteristics of one machine and two uses.
橡膠雙頭磨片機技術參數：
★砂輪線速度：12米/秒
★砂輪規格：G60APRI170×40×32 36粒
G60APRI170×40×32 80粒
★電動機：GO-11-40.6瓦三相380V，2845轉/分
★工作尺寸：直徑160×44mm，中間高214mm
★工作輪行程：20毫米
★夾持試樣尺寸：長度大于260mm；寬度大36mm；厚度大8mm
★外形尺寸：500×400×341mm
★凈重：80公斤
Technical parameters of double-side rubber mill:
★ Wheel speed: 12m / s
★ Grinding wheel specifications: G60APRI170 × 40 × 32 36 grains
G60APRI170 × 40 × 32 80 capsules
★ Motor: GO-11-40.6 Watt three-phase 380V, 2845 rpm
★ Working size: diameter 160 × 44mm, middle height 214mm
★ Working wheel stroke: 20mm
★ Clamping sample size: length is more than 260mm; width is 36mm; thickness is 8mm
★ Dimensions: 500 × 400 × 341mm
★ Net weight: 80 kg
橡膠雙頭磨片機使用方法：
★撥動小手把，使?jié)L花偏心球張開，將橡膠試片的一端夾入，再將試片的另一端逆時針方向，沿著工作輪運用活動壓棍壓好。
★啟動電動機，使砂輪向著前頭所示方向轉動。
★搖動手柄，使上拖板沿著下層軌向著進給，手柄上裝有刻度盤，每小格為0.02毫米。
★撥動手輪中裝有保險裝置。手輪只許朝逆時針方向轉動，反之用力過猛將會損壞其保險裝置。
★磨片機在工作時應先粗磨、后細磨。
How to use the double-head rubber mill:
★ Push the small handle to make the knurled eccentric ball open, clamp one end of the rubber test piece, and then press the other end of the test piece counterclockwise along the working wheel to press it down.
★ Start the motor and turn the grinding wheel in the direction shown at the front.
★ Shake the handle so that the upper carriage feeds along the lower rail. The handle is equipped with a scale, each grid is 0.02 mm.
★ The safety device is installed in the handwheel. The handwheel can only be turned counterclockwise, otherwise excessive force will damage its safety device.
★ Grinding machine should be rough ground first and fine ground later.
橡膠雙頭磨片機維護與保養：
★如發現磨出的試片厚度不均及不平整現象，應檢查砂輪平面是否下平行。
★如發現砂輪有失調失圓現象，應用割刀修正平面。
★定期給拖板工作面加潤滑面，以保持正常工作。
★經常調整螺母與絲桿的間隙大小。
★該機安裝在無震動及無來源的環境中。
Maintenance and maintenance of rubber double-head grinding machine:
★ If uneven thickness and unevenness of the test piece are found, check whether the plane of the grinding wheel is parallel.
★ If the wheel is found to be out of balance, use a cutter to correct the plane.
★ Add lubricating surface to the working surface of the pallet regularly to keep it working normally.
★ Always adjust the gap between the nut and the screw.
★ The machine is installed in an environment with no vibration and no sources of corruption.
