鹽城遠洋泵業有限公司
會員1.png)
一、用途：
1.5GCJ-5 型單吸多級分段式離心泵，供輸送 110 ℃以下的清水及物理化學性質類似于水的液體，適用于鍋爐給水、工廠和城市給水等。
1.5 ——吸水口直徑（毫米）被 25 除得值并化整
G ——鍋爐給水泵
C ——表示泵的種類
J ——機械密封式
5 ——縮小為 1/10 泵的比轉數。即泵的比轉數為 50
6 ——葉輪的數量
General Description
Type 1.5GCJ pump is centrigugal pumps of single suction and multi-stage segmental type which can be used to transport clean water and liquids with physical and chemical nature similar to water.The liquid temperature is not higher than 110 ℃ .It is suitable for water feeding to boilers,ａnd water supplying to factories and cities.
Designation of 1.5GCJ — 5 × 6
1.5 —— Suction diameter(mm)divided by 25 , and then change the Value into integer
G —— Boiler feed pump
C —— Indicating type of te pump
J —— Mechanical seals
5 —— Specific speed divided by 10 (i.e.the specific speed of the pump is 50)
6 —— Number of impellers
性能表 PerformanceChart
結 構 圖 Sectional View
| 1、軸套螺母 | 1 、 Sleeve nut | 2 、軸承蓋 | 2 、 Bearing Cover |
| 3, 軸承 | 3 、 Bearing | 4 、軸承體 | 4 、 Bearing body |
| 5 、軸套 | 5 、 Sleeve | 6 、填料壓蓋 | 6 、 packing glａnd |
| 7 、機械密封 | 7 、 Sealing machine | 8 、進水段 | 8 、 Suction casing |
| 9 、密封環 | 9 、 Wearing ring | 10 、葉輪 | 10 、 Impeller |
| 11 、中段 | 11 、 Midsegment | 12 、回水管 | 12 、 Balance pipe |
| 13 、出水段 | 13 、 Discharge casing | 14 、平衡環 | 14 、 Balancing ring |
| 15 、平衡盤 | 15 、 Balancing disk | 16 、尾蓋 | 16 、 End cover |
| 17 、軸套 | 17 、 Sleeve | 18 、拉緊螺栓 | 18 、 Tightening |
| 19 、軸 | 19 、 Pump shaft | 20 、圓螺母 | 20 、 Round nut |
結 構 說 明 Construction
泵的進出口方向均垂直向上，為根據所需揚程選用不同級數。
泵的定子部分由進水段、中段、出水段、尾蓋和軸承體等零件組成。
泵的轉子部分由軸、葉輪、軸套和平衡盤等零件組成，兩端支撐在滾珠軸承上。
泵的進水段、中段、出水段靜止結合面采用紙墊通過緊螺栓的拉緊來達到密封。為防止水進入軸承、在軸套間裝有“○"形密封圈。泵體兩端軸封采用機械密封。
泵兩端軸承體有環形冷卻室。當被輸送液體大于 80 ℃時，應通入冷水，對軸承進行冷卻。
軸承內的鈣基黃油潤滑脂可通過油杯注入。
從進水段方向看，泵為順時針轉動。
The directions of suction and discharge of the pump are all vertical and upward .with different stages selected according to the needed head.
Stator of the pump is composed of suction casing .mid-segment.discharge casing .end cover and bearing body.
Rotor of the pump is composed of shaft.impellers.sleeves,ａnd balancing disk,The two ends are supported by the ball-bearings
Paper gaskets are used on the contacting surfaces between the suction casing.mid-segment and discharge casing of the pump.They are sealed by tightening the bolts. ○ -rings are mounted on the interfaces between the sleeves to prevent water from entering the bearnjngs. ○ ilimmersed machine is sealing at the two ends the pump.
There are water cooling jackets around the bearing housings.when the temperature of liquid is higher than 80 ℃ ,Cooling water should be turned on to cool the bernings.
Calcium grease lubricant is firled into the bearing thrugh oil-cups.
Viewing from the direction of the suction casing .the pump is rotating clockwise
性 能 曲 線 Performance Curves
注：該圖為單級揚程 Note curves are plotted with reference to single-stage pumping head
安裝尺寸圖 Overall Dimensions
安裝尺寸表 Installation Dimensions
Promotional products
4DZY電動自動試壓泵（2023-12-26）
4DSY電動試壓泵（2023-12-26）
SJ系列不銹鋼深井泵（2023-11-20）
CQ磁力泵（2023-10-27）
YYJ-1計米印字機（2023-10-10）
YYJ-2計米印字機（2023-10-10）
CW型磁力驅動旋渦泵（2023-07-06）
CW型磁力旋渦泵（2023-07-01）
IH型化工泵 IH型不銹鋼離心泵（2023-03-02）
包裝印刷網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
